Zestaw eksploatacyjny do zgrzewarki PFS/ABS - NovumPack
Forgot your details?
Create account

Zestaw eksploatacyjny do zgrzewarki PFS/ABS

36.00 76.00  + VAT

Zestaw eksploatacyjny pasuje do wszystkich zgrzewarek z serii FS/PFS. Prosimy wybrać konkretny model.

Wyczyść

Opis

Zestaw eksploatacyjny PFS pasuje do wszystkich zgrzewarek z serii FS/PFS. Prosimy wybrać konkretny model.

Zestaw eksploatacyjny PFS zawiera:

  • PFS100-500: 2 teflony i 2 elektrody
  • PFS200-500C: 2 teflony, 2 elektrody, 2 ostrza noża
  • PFS300-400M: 2 teflony, 2 elektordy, 2 ostrza noża

Dodatkowe informacje

Waga 1 kg
Wymiary 20 × 30 × 5 cm
Model urządzenia

PFS100 2mm, PFS200 2mm, PFS200C 2mm, PFS200M 2mm, PFS200B 8mm, PFS300 2mm, PFS300 3mm, PFS300C 3mm, PFS300M 3mm, PFS300B 8mm, PFS400 3mm, PFS400C 3mm, PFS400B 8mm, PFS400K 5mm, PFS500 3mm, PFS500C 3mm, PFS500K 5mm, ABS200 2mm, ABS300 2mm, ABS4002mm

Jak wymienić elektrodę i teflon?

Replacing the sealer wire can seem to be intimidating and dangerous. However it can be a very painless and a money saving endeavor.
This article will hopefully make it simple and not so foreign to you and get your production back up and running.
Some of the signs that you need to replace the sealing wire:

  • It takes longer than normal to seal a bag.
  • The seal is not complete.
  • The sealer won’t seal when the bar is pressed down.
  • The Teflon® strip is burnt.
  • The heating sealing wire is broken in two

note: Be sure to unplug the sealer before attempting any of the following steps.

Steps

  1. Image titled Replace an Impulse Heating Sealer Wire Step 1
    1
    Remove the screws that hold the metal plates that are found on both sides of the sealer.
  2. Image titled Replace an Impulse Heating Sealer Wire Step 2
    2
    You will need a Phillips head screwdriver for removing the screw that holds the wire. Be sure to keep fingers on the screw as it can “POP” away from the sealer since the wire is under tension.
  3. Image titled Replace an Impulse Heating Sealer Wire Step 3
    3
    Pry the tensioning pin away from the hinge with a standard or flat blade screwdriver. Using a Philips head screwdriver won’t work because the pin, that is under tension, will spin and make it very difficult to allow you to remove the heating element wire off of the pin.
  4. Image titled Replace an Impulse Heating Sealer Wire Step 4
    4
    Remove all parts of the broken sealing wire, and pry the pin away from the hinge so that you can place the the new element on the pin.
  5. Image titled Replace an Impulse Heating Sealer Wire Step 5
    5
    Keep holding the new element wire while keeping tension on the wire. Slowly allow the the tensioning pin to come to a rest.
  6. 6
    Place the metal plates that hold the Teflon® strip back into place on both sides of the sealer. Do not tighten them down completely. When both metal plates have the screws holding them in place, place the Teflon® strip evenly under both plates and tighten the screws down.
BE SURE THAT THE TEFLON® STRIP IS PLACED FIRMLY AGAINST THE HEATING ELEMENT WIRE.
Image titled Replace an Impulse Heating Sealer Wire Step 6
  1. Image titled Replace an Impulse Heating Sealer Wire Step 7
    1
    Take the screw that holds the element wire and screw it back in.

Opinie

Na razie nie ma opinii o produkcie.

Napisz pierwszą opinię o “Zestaw eksploatacyjny do zgrzewarki PFS/ABS”

Twój adres email nie zostanie opublikowany. Pola, których wypełnienie jest wymagane, są oznaczone symbolem *

TOP